메뉴 건너뛰기


림돌이 TS-2에 대한 해석좀

목우2005.09.10 15:44조회 수 536댓글 1

    • 글자 크기


림돌이를 사용하기전에 셋업하는 사항인데 해석하기가 참으로 힘듭니다
해석 좀 부탁드릴께요
http://www.parktool.com/repair/readinstructions.asp?id=86

CENTERING THE TS-2


This article will discuss the centering of the TS-2 truing stand. Also see related articles:


◦ ◦ Wheel Dish or Centering
◦ Wheel Truing◦ Wheel spoke tension


The TS-2 truing stand is adjusted at the factory to center the rim between the calipers. With use, the TS-2 can come out of center. For precision work, the TS-2 is intended to be used with a dishing tool, such as the Park Tool WAG-4 or WAG-3.
It is common for wheels and hubs to have anomalies that affect centering. The axle and bearing may not be exactly concentric. To check and adjust the TS-2, you will need a properly centered wheel, either front or rear, or the Park Tool 1554-1 centering gauge. Double check the wheel using a dishing tool. Do not assume a new wheel is properly dished.
NOTE: Older stands can benefit from the TS-RK rebuild kit. Contact Park Tool for the TS-RK.
There are three versions of the TS-2 in use. Older model TS-2's have no spring between the shaft collars on the main shaft. Some models have a spring between shaft collars to insure collars are pushed outward. Older models using the setscrew type collar used silver colored collars. Current model TS-2's use a black split ring type shaft collars, a spring, and thrust bearings on the main

Begin by checking for excessive play in the uprights. Grab either upright and move it left to right. A small amount of play is normal. If there is play, look at the shaft collars. If you can see the collars move left to right significantly, there is excessive play. Remove play and re-center the uprights, as described below. Also check for free movement of the caliper's themselves. Pull outward on each caliper. Adjust as necessary by using the nut behind each caliper.

If TS-2 is slightly out of alignment (3mm or less), adjust using caliper arm locknuts. The caliper arm is attached to the base with two nuts, one on the left side and one on the right. The calipers at the rim can be moved either left or right using these nuts at base of arm. Assume a dished wheel shows a gap at the caliper on the right side. The calipers can move to the left. First, loosen the right nut 1/4 to ½ turn and tighten left locknut same amount. Reverse process to move caliper toward the right. Repeat as necessary.

If the TS-2 is off significantly, it may be necessary to adjust the upright arms that grab the hub.
1- Loosen bolt or setscrew on both collars located between base uprights. Hold collar and spin adjusting knob is check that collars are loose from main shaft. Push arms side to side to double check shaft movement in collars. Older models have set screw collars. The set screw drives directly into the main shaft. Upon loosening set screw it may be necessary to use pliers to free collar from burr on main shaft. Newer models have "split ring" collars and pinch the main shaft.

NOTE: Some shaft collars use a 3.5mm hex key (9/64").

4- Install dished wheel into moving uprights and secure upright adjusting knob until arms are gently snug on axle locknuts.
5- Grab upright arms and pull arms left and right until rim appears centered between base uprights. Measure using caliper from rim to each base upright to check centering.
6- For Setscrew-Type-Collars: place feeler gauge of 0.003" (or a piece of paper) between collar and base upright. Secure collar set screws. Remove gauge or paper.
6a.- For split ring collars simply secure set screws using no shim. Thrust bearing take place of shim.

6b.-For older stands with no spring between collars, place a shim against base upright and push each collar against its appropriate upright. Secure set screw.
7- Raise caliper arm to rim level and open calipers.
8- Slowly close calipers close to rim and note centering.
9- To move calipers, use caliper arm pivot nuts at base of caliper arm. To move calipers left, loosen right nut 1/4 to ½ turn and tighten left locknut same amount. Reverse process to move caliper right. Repeat as necessary until caliper center on rim.
10- TS-2 is ready for use. Again, for the most accurate work, TS-2 should be used with a dishing tool.





    • 글자 크기
머린데칼 문의드립니다 (by kweon8015) MTB 입문 할려고 합니다. Elfame Alpha600 과 TXC530, TXC500 비교 추천해주세요 (by inhwaj)

댓글 달기

댓글 1
번호 제목 글쓴이 날짜 조회 수
공지 ::: Q/A 게시판의 이용방법을 알려드립니다 :::35 Bikeholic 2002.12.05 138931
54882 크랭크 스윙암 길이문의 드려요3 시원한 맥주 2005.09.10 193
54881 머린데칼 문의드립니다1 kweon8015 2005.09.10 242
림돌이 TS-2에 대한 해석좀1 목우 2005.09.10 536
54879 MTB 입문 할려고 합니다. Elfame Alpha600 과 TXC530, TXC500 비교 추천해주세요2 inhwaj 2005.09.10 318
54878 중고 입문용 자전거 문의드립니당.3 mfuture 2005.09.10 251
54877 폭스 rlt100 와 fx100에서 갈등중인데요,,,어떤샥이 나을까요...2 wagle 2005.09.10 393
54876 커스텀 주문할때 자신의 신체는 어디서 측정해야 하나요?1 태후니 2005.09.10 209
54875 15.5 인피 프레임을 구매했습니다1 zmd2930 2005.09.10 209
54874 [사진 있음]레이싱자켓이 신형,구형인지 답변좀 부탁드립니다.3 2005.09.10 397
54873 왈바에서 파일을 올리는 방법2 목우 2005.09.10 160
54872 전문샾.. sws777 2005.09.10 171
54871 06년 시드시리즈가3 무적민수 2005.09.10 440
54870 스캇 mtb슈즈 발볼너비문의 hb2429 2005.09.10 327
54869 06년도 타사자라..2 rockerok 2005.09.10 509
54868 휠셋 많이 판매하는 쇼핑몰???? 태고 2005.09.10 194
54867 QR레버 색상 문의8 WILD 곰돌 2005.09.10 369
54866 xt구형(4피스톤)디스크브레이크 레버1 darock612 2005.09.10 259
54865 져지...골라주세요..(날리니,스고이,아소스,펄이즈미)1 aqr29jy 2005.09.10 1040
54864 [질문] 마조찌 EXR COMP 03 샥에 대해 자세히 아시는분?~?~?^^2 ayukawa777 2005.09.10 350
54863 캣아이 HL-EL500 라이트 1개 VS 파워빔 2개4 ak1jak1 2005.09.10 688
첨부 (0)
위로